Quick Answer: How Many Amps Does A 1 1 2 Hp Motor Draw?

How many amps does a pump draw?

Divide the wattage by the voltage to find the current.

For example, if the pump wattage is 2,200 watts, and the voltage is 110 volts, the current is 2,200 /110 = 20 Amps.

This is the value of the amps drawn by the well pump..

How much electricity does a 1hp motor use?

Here, we have a 1 HP motor. So, 1 HP for 24 hour = 746×24= 17904 Watt-hour which is equal to 17904/1000= 17.904 units. Hence, 17.904 units of Power will be consumed by the 1 HP motor when run continuously for 24 hours.

How much is 2 horsepower?

Hp to Watts Conversion TableHorsepowerWattsRounded Watts1 hp745.699872 W746 Watts2 hp1491.399744 W1491 Watts3 hp2237.099616 W2237 Watts4 hp2982.799488 W2983 Watts96 more rows

How many amps does a above ground pool pump use?

A typical above ground pool pump will require a 20-amp breaker and use #12 gauge wire to deliver the electricity.

How many amps does a 1 1 2 HP well pump draw?

5.0 ampsMaximum Load is what the motor would be delivering when service factor is included. As a result, Maximum Load is often also referred to as service factor amps or max amps. Taking the 1/2 hp, 230 V example, when delivering 1/2 hp to the pump it draws 5.0 amps.

How many amps does a 2 hp motor draw?

Common Horsepower to Amps ConversionsHorsepowerAmpsVoltage2 HP13.8 A120 V2.5 HP17.3 A120 V3 HP20.7 A120 V3.5 HP24.2 A120 V11 more rows

What size breaker do I need for a 5 hp motor?

How to Calculate How What Size Circuit Breaker a Machine will Need:HorsePower of Main Motor220 Volts, 1 phase220 Volts, 3 phase52814633.616.8739.219.6844.822.411 more rows

How many amps does a 1.5 HP 3 phase motor draw?

AC Motor Full Load AmperesHP200 Volts440-480 Volts14.82.11.56.93.027.83.43114.823 more rows

How many amps does a 1 HP pool pump draw?

10 to 12 ampsSince it’s an aboveground pool pump it’s an uprated model and probably draws in the neighborhood of 10 to 12 amps at 120 volts. Depending on your plumbing it may draw less.

How many HP is 15 amps?

At 100% efficiency, the most a 15-amp, 120v outlet in a home circuit can supply is 15 x 120 or 1800w; 1800 divided by 746 equals 2.41 hp.

How many amps does a 1 hp motor draw?

AMP DRAW BASED ON HORSEPOWERHP1 Phase Amps3 Phase Amps115 volt230 volt1164.21-1/22062246.812 more rows•May 21, 2020

How do you convert HP to amps?

Multiply amps by volts to obtain the motor’s wattage, or watts (A * V = W). Wattage is the same type of unit as horsepower, a measure of power, so it can readily be converted (like gallons to quarts). The wattage for the blender example would be 5 A * 115 V = 575 W.

How many watts is a 1.5 HP pool pump?

It’s not uncommon for a 1.5 horsepower pump to use 1500 – 2000 watts. This is unfortunate, because most pools only need 1/4 to 1/8th horsepower for circulation. Higher power may be needed for tasks like vacuuming the pool.

How many watts does a 1 HP pool pump use?

A single-speed pump drawing 2,000 watts, operating at 3,450 rpms and generating a flow rate of 66 gallons per minute can turn over the entire 25,000 gallons of water in roughly 6.3 hours. At this rate the single-speed pump would consume 12,600 watt hours or 12.6 kWh per day, to turn over the pool.

How many amps does a 1.5 hp motor draw?

1 Horsepower is 745.7 watts, so a 1.5 HP motor would require a maximum of 1118.55 watts. 1118.55 W / 220V equals 5.084 amps, so in theory your motor will need just over 5 amps of current.

How many watts is a 1.5 hp motor?

1125 watts1hp equal to 750 watts so 1.5. hp equal to 1125 watts .

How many amps is a pool filter?

If you need to know the electrical requirements for your inground pool, here is a list of common pool equipment and the approximate volts and amps required for each: Pool Pump: 240v, 10amps. Salt Water Chlorinator: 240v, approx 5-8 amps. Pool Heat Pump: 240v, 50 amps.

How many amps does a 1.5 HP pool pump draw?

In our example we used a 1.5HP Hayward Super Pump. The voltage rating is 115/230 and the amp rating is 18.6/9.3. If you run a pump on the lower voltage rating (115) you will select the higher amperage rating (18.6).

What size breaker do I need for a 1/2 HP well pump?

For a 1/2 HP submersible pump, a 15 amp 2 pole breaker would be normal. You can run 12 AWG, but unless the run is very long, 14 AWG is sufficient. Bigger wire would let you switch to a bigger pump later if you wanted.